The Wobble Wedge

June 7, 2019

TOOLS THAT DON’T SUCK

As water feature installers, my sons and I are used to hard, dirty, sometimes dangerous work. We enjoy what we do, whether it’s digging ponds, plumbing pumps, rolling boulders or tweaking waterfalls. We also value anything that helps make the work easier or more fun. We’re always looking for tools, apps or gadgets that save time & effort, eliminate stress, add to our comfort on the job or are just fun to use. Often a buddy will turn us on to one. I’d like to return the favor by passing our favorite Tools That Don’t Suck along to you.

The Wobble Wedge

Sometimes the best stuff comes in the smallest packages. That’s the way I think of this next doohickey. This deceptively simple device that’s so well engineered that I now take them for granted. But that’s only because I keep a jar full of them in every truck. I’m talking about the modest, overachieving Wobble Wedge.

Photo from WobbleWedges.com

The manufacturer calls them “a modular system of securely-stackable interlocking plastic shims”. Like any good system, there are a number of models to choose from. There are flexible and rigid wedges, white, black or clear in color. Three different sizes, all interlocking and cross-nesting, accommodate all sorts of leveling, shimming, tightening and locking tasks in and out of doors. All feature tiny ribs that lock wedge-to-wedge, regardless of the size of the wedge.

Wobble Wedge, Basalt Column
Can be adjusted in tiny increments and lock where you leave them.

For our purposes, we like the rigid standard black wedges for shimming columns and overflowing vases that need small adjustments, while the Big Gap wedges handle really uneven situations. Regardless of the size, all Wobble Wedges can be adjusted in tiny increments and lock where you leave them, no slipping or shifting.

Are they worthy of the status “Tools That Don’t Suck?”

Heck yes! These guys thought of everything that I could want on the job, and they have a couple of patents to prove it. The standard black Wobble Wedges are small and easily concealed. The hard plastic is pretty much indestructible. I say that after shimming over a thousand pounds with them, driving them home with a mallet to get a granite sphere dead level. They’re even forgiving! If you push them too far under a really big fountain or stone column, they have an inset Grab Bar at the back of the wedge that lets you pull them back out with a needlenose plier.

Wobble Wedge, Basalt Column
Grab Bar at the back of the wedge that lets you pull them back out.

Did I mention that they are 100% Made in the USA? And they’re inexpensive to boot, around $20 for a bucket of 75! When I showed one to my friends at a distributorship I was visiting, they brought them in the next day, no further convincing necessary. Love at first sight. 

If you haven’t already, try Wobble Wedges. I think you’ll like them.

Also check out or blog on the Atlantic Eco-Rise System to create reservoirs of practically any size, shape and volume supporting any number of decorative items with complete adjustability.

Atlantic Cord Seal Fitting

A great new way to hide power cords!

Even the nicest water feature installation can be ruined if the cord for a pump or a light is visible, as they often are. Power cords should be removable, so that lights or pumps can be serviced or eventually replaced. They can’t just be buried away in concrete. With open reservoir water features, like ceramic vases or copper basins, a hole in the reservoir that’s big enough to pass a plug is hard to seal, and cutting the plug off voids the warranty on pumps and lights.

Wouldn’t it be great if a power cord could pass through the same bulkhead fitting that the water feeds through? Without leaking? That way, a light could be set inside the reservoir without a cord draping over the edge, or a pump cord inside a basin could pass through a plumbing fitting, virtually invisible. But, even if you ran a cord inside a pipe from inside the reservoir, how would you get it back outside of the pipe, outside of the reservoir?

Atlantic Cord Seal Fitting

Enter the CSF. The Cord Seal Fitting is a nifty gadget that addresses that particular need, to pass a cord through the wall of a reservoir inside the fitting or pipe that is the reservoir’s only perforation. It works much like a plumbing pressure test plug. A rubber gasket squeezed between two plates expands outwards and seals off a 1-1/2″ female socket. But, unlike a test plug, the rubber doughnut is slit to its center to accept a standard light or pump cord. The plates on either side of the gasket are also split, to assemble around the cord and gasket like the cookies around the creme of an Oreo. When tightened, the rubber expands tightly around the cord and into the fitting, creating a waterproof seal.

As is often the case, the Cord Seal Fitting is far easier to use than to describe. Install a tee in the 1-1/2″ waterline feeding the reservoir and pass the cord through the tee and into the reservoir. Loosen the plates on the CSF, slide the cord into the gasket, reattach the plates and tighten the CSF in the opening of the tee. The gasket will expand and seal against the cord and the inner walls of the tee.

The CSF will also allow the cord to pass in and out of a sealed section of pipe, with the addition of a second tee. This is useful where a pump may be hard piped from the inside of a reservoir, out through a bulkhead fitting and up to a spillway. The illustration to the right shows the pump cord passing out of the reservoir through tees through a tee installed on either side of the bulkhead fitting and sealed with Cord Seal Fittings inside and out.

Another great solution from the folks at Atlantic!

The Atlantic Eco-Rise System

Bubbling Basalt Columns and overflowing vases set on buried Fountain Basins are attractive, easy and profitable add-ons for the irrigator, landscaper or hardscaper. These water features are especially popular with contractors who only occasionally venture into water (so to speak) because they are simple to build, easy to maintain and rarely require call-backs. As a bonus, the successful completion of one project usually leads to another, as friends, visitors and neighbors ask about the fountain and decide to put one in for their own enjoyment. But what happens when the next job requires a boulder too big for the basin? A vase too vast? A mountain of a fountain?

The “Old” Way

In the old days, BA (Before Atlantic), installing a one-ton fountain piece, like a 36″ granite sphere, was a month-long project. The contractor would design a concrete basin large enough to catch splash and strong enough to handle the load. Waterproofing would depend on climate. In the north, the design would have to deal with freeze/thaw cycles and excavating below the frost line. After digging to the proper depth and tamping the bottom, the plumbing would need to be set, with no room for error, as it would literally be set in stone. Then the concrete trucks would arrive. After the four-week curing period (ouch!), the sphere could be carefully lifted by machine, plumbed in the air, then lowered into place, hopefully without crushing the plumbing.

The “New” Way

The Atlantic Eco-Rise System allows two men with two wheelbarrows to complete a two-thousand-pound granite sphere fountain install – in two days. Like most good systems, it’s simple, with only three structural components, plus liner, pump and plumbing. Instead of formed and poured concrete down to the frost line, the reservoir is just a rubber-lined hole a single layer of Eco-Blox deep. The Eco-Blox may look like milk crates, but the similarity ends there. Our Blox come disassembled, lock solidly together and support 7 tons of distributed load without crushing.

The Eco-Rise is a load distributor that supports the sphere, and much more. Rated at three thousand pounds, the Eco-Rise spreads the weight of the stone across the tops of the Eco-Box while protecting the plumbing. Install the pipe into the sphere, roll it onto the Eco-Rise on the Eco-Blox. With the flex pipe in place, the sphere can easily be moved and adjusted by hand, without a machine!

The third component, the PV1700 Pump Vault, houses and protects the pump. Hook the pipe to the pump in the Vault, and you can adjust the sphere, by hand, even while running. Then, cover  the Eco-Blox with two wheelbarrows of gravel and go home early.

Atlantic. We’ve got you covered.